- 120 VOLT WATER WELL BLADE DESKCONNECT HOW TO
- 120 VOLT WATER WELL BLADE DESKCONNECT INSTALL
- 120 VOLT WATER WELL BLADE DESKCONNECT PLUS
That metal thing which I plug into the DC gets extremely hot very quickly in matter of minutes also. I had to wiggle the adapter to the power connector of the notebook or my laptop battery won’t charge and won’t turn on if it doesnt have it’s battery on. I’m having similar problems with my Compaq Presario M2000 notebook too. Thanks for the step by step instructions I got my computer going and it feels realy good to know that their are people out there that can hep out and make a difference and save some major dollars. It wasn’t to hard and I got it fixed by my own hands and just paid $15.00 for the solder iron. After finding this sight I went to the store to buy me a soldering iron and took apart my computer for the first time. I went back home thinking about buying a new one then I used my other computer to see if I could get help on the internet to fix it. Then they told me that it would be better to just get a new computer instead of fixing it.
120 VOLT WATER WELL BLADE DESKCONNECT PLUS
Took it to a repair shop some 100 miles from my home and they told me that I would have to get a new mother board and other thing plus labor cost it would run around $650.00 to repair my computer. The battery would not charge and the power could not get to turn on my computer.
120 VOLT WATER WELL BLADE DESKCONNECT INSTALL
Now just install the motherboard back into the laptop and you are done. The job is done and the laptop DC power jack is fixed. Now you are ready to solder the jack back in place. Put something under power jack so there is no gap between the jack and the motherboard. Now you can install the power jack back on the motherboard.
It’s not necessary but it will make your job looking clean.Īpply a fresh coat of solder to all power jack terminals on both sides of the motherboard. You can remove the flux using the tooth brush and alcohol. The power jack terminals will look dirty because of melted flux. I hope you understand what I’m talking about.Īfter the power jack is removed, clean all oxidized contacts with a knife.Īpply a fresh coat of solder to all contacts on the power jack. So, do not apply any force and make sure the solder is melted when you are removing the power jack.
120 VOLT WATER WELL BLADE DESKCONNECT HOW TO
UPDATE: If you accidentally removed the internal sleeve, check out this post: How to fortify damaged power jack connection. If you are removing the power jack with force, you can pull the sleeve from the hole. Inside the positive hole there is a copper sleeve which connects the terminal on one side of the motherboard with the traces on the other side. The DC power jack is almost removed from the motherboard.īe careful. This will help you to remove the power jack. Carefully wiggle the power jack without applying any significant force and at the same time heat up all contacts one by one.
Most likely you will not be able to remove the power jack the first time because there will be some solder bridges left between the contacts and traces on the motherboard. Grab the power jack and carefully try removing it from the motherboard. Repeat the same steps with all power jack contacts until you remove as much solder as possible. While heating one of the contacts, remove the solder from this contact using the desoldering pump. This will make old solder more flowable, easier to remove. Start desoldering process with adding some new fresh solder to all three contacts. I’m going to desolder the power jack from the motherboard, clean contacts on both power jack and motherboard and then solder it back in place – this is the proper way fixing the power problem.
The positive pin is not making a good contact with the motherboard and because of that power to the laptop cuts off when I move the power plug inside the power jack. 99% isopropyl alcohol and tooth brush for cleaning the motherboard from flux.Īs you see on the following picture, the solder drop on the positive terminal looks different than on other three contacts. I use Edsyn Soldapullt pump, model DS 017.Ĥ. Desoldering pump for removing solder around component leads. I think standard rosin core solder will work just fine.ģ. I use high-tech rosin core silver-bearing solder from Radioshack with diameter 0.022″ ( Catalog #: 64-013 ). I use Weller WES51 soldering station and for this job I set temperature to about 800-850☏.Ģ. For this repair you’ll need the following tools.ġ.
0 kommentar(er)
